EXPERIMENTAL STUDY OF TEMPERATURE EVOLUTION AND IDENTIFICATION OF INSTABILITY POSITION OF PLANAR STRIKE-SLIP FAULT DURING PROCESS OF STICK-SLIP          下载免费PDF全文

REN Ya-qiong  MA Jin  LIU Pei-xun  CHEN Shun-yun 《地震地质》2016,38(1):65-76

Stick-slip of fault in laboratory accompanies change of temperature. Temperature change is not only concerned with sliding friction, but also with the stress state of the sample. In this article, we use infra-red thermal imaging system as wide-range observation means to study the temperature variation of different stages during the deformation of sample. The rock sample for the experiment is made of granodiorite from Fangshan County with a size of 300mm×300mm×50mm. It is cut obliquely at an angle of 45°, forming a planar fault. Two-direction servo-control system was used to apply load on the sample. The load in both directions was forced to 5MPa and maintained constant (5MPa) in the X direction, then the load in the Y direction was applied by a displacement rate of 0.5μm/s, 0.1μm/s and 0.05μm/s successively. The left and below lateral of the sample were fixed, and the right and top lateral of the sample were slidable when loaded. The experiment results show not only the temperature change from increase to decrease caused by conversion of stress accumulation to relaxation before and after the peak stress, but also opposite variation of temperature increase on fault and temperature decrease in rock during instability stage. Most important of all, we have found the temperature precursor identifying the position of instability through the temperature variation with time along the fault. It shows that rate of temperature increase of instability position keeps relative high value since the stage of strongly off-linear stage, and accelerates in stage of meta-instability. After separating the effect of friction and stress, we found that temperature increase occurs in the rock near the fault instead of on the fault, which means the mechanism of temperature increase is stress accumulation. Temperature of fault at the instability position does not increase, which means the position is locked. We speculate that the position of locked area on fault with high stress accumulation near the fault may be the future instability position. It is of significance of studying temperature variation during stick-slip to the monitoring of earthquake precursors. Heat caused by friction of earthquake needs long time to transfer to the surface and could not be detected as a precursor. While the stress of surface rock near the fault would change as the stress of interior rock changes, which could cause detectable temperature variations. The research purpose of this article is to find special change positions before instability. As the temperature variations are caused by stress and slip of fault, the results are also meaningful to analysis of stress and displacement data related to earthquake precursors.  相似文献   

营口-潍坊断裂带新生代运动学特征   总被引：6，自引：0，他引：6  

姜建平 《海洋地质与第四纪地质》2008,28(4)

营口-潍坊断裂带在新生代时期对渤海湾盆地东部构造、沉积及油气成藏规律等方面具有重要影响和控制作用.依据大量实际地震资料,从剖面上识别出了花状构造、丝带效应、反转构造等营口-潍坊断裂带新生代时期走滑活动的标志,在平面上识别出了4种组合构造样式,在此基础上,应用拉分盆地走滑量计算的理论模型,对营口-潍坊断裂带新生代时期的走滑位移量进行了初步估算,认为营口-潍坊断裂带在新生代时期具右旋走滑活动特征,其主要走滑活动表现为3期,分别为始新世早期、渐新世早-中期和上新世晚期-第四纪,新生代累计右旋走滑位移量约为10～20 km.  相似文献   

完达山区旋卷构造与找矿意义     

刘发文  梁树昌 《中国煤炭地质》2014,(12):81-88

完达山区旋卷构造位于黑龙江省东部,发育于完达山优地槽褶皱带内,构成饶河复背斜。该复背斜总体呈近南北向,略向西突出的弧形逆掩推覆于宝清过渡带。用旋卷构造＂三大特征＂对比,一系列弧形褶皱和断裂向北东方向收敛,向南东方向撒开,围绕以蛤蟆河岩体为中心旋扭,内旋面向撒开方向、外旋面向收敛方向旋扭,具压性—压扭性特征。这一旋卷构造是由富锦——小佳河断裂的剪切牵引为主、敦密深大断裂的左旋走滑剪切为辅的联合作用形成的。根据旋扭构造的发育情况大体划分了三个旋扭层。目前已知的铜金矿（点）床主要分布于各旋扭层的撒开段,但收敛段找矿潜力较大,其次为各旋扭层界面和向西弧形突出部位也具一定的找矿潜力。  相似文献   

Palaeostress analysis of the northern Nijar and southern Vera basins: constraints for the Neogene displacement history of major strike-slip faults in the Betic Cordilleras, SE Spain     

Paul Huibregtse  Hans van Alebeek  Matthijs Zaal  Cees Biermann 《Tectonophysics》1998,300(1-4):79-101

This paper presents the results of a detailed structural analysis of the northern Nijar and southern Vera basins with special emphasis on the evolution of the regional stress field and the associated timing of movement of the Serrata, Gafarillos and Palomares strike-slip fault zones. These major fault zones control the Neogene deformation of the SE Internal Betic Cordilleras in Spain. Detailed stress analysis on Neogene sediments of the Vera and Nijar basins shows a strike-slip regime with NW–SE-oriented subhorizontal maximum principal stress (σ₁) during Tortonian and earliest Messinian times. Under the influence of this stress field, dextral displacement along the N090E-trending Gafarillos fault zone resulted in deformation of the sediments of the southern Sorbas and northeastern Nijar basins. During the early Messinian a clock-wise rotation of the stress field occurred. Stress analysis in rocks with late–early Messinian up to Quaternary ages in the Nijar and Vera basins indicates a strike-slip regime with N–S-oriented subhorizontal maximum principal stress (σ₁). Under the influence of this stress field the main activity along the N010E-striking Palomares strike-slip fault zone took place, resulting in deformation of the Neogene sediments of the southeastern Vera basin and culminating in a maximum sinistral displacement of more than 20 km. At the same time the stress field was not suitably oriented to exert a large shear component on the Gafarillos fault zone, which activity ended after the earliest Messinian. Fault and outcrop patterns of syntectonic Neogene sediments in the Vera basin show that displacement along the Palomares fault zone decreased at the end of the Middle Miocene although minor displacement phases may still have occurred during the Late Miocene and possibly even Pliocene. From the Middle Miocene onward, deformation in the Nijar basin was controlled by sinistral displacement along the N040E-trending Serrata strike-slip fault zone.  相似文献   

一个韧性转换挤压带的变形分解作用：以阿尔金断裂带东段为例   总被引：28，自引：3，他引：25  

张建新  许志琴 《地质论评》1998,44(4):348-356

变形构造研究显示阿尔金划分成具有近水平拉伸线理的韧性左行走滑变形域和具有陡角度倾伏拉伸线理的收缩变形域。在ＳＳ与ＰＳ之间的过渡区域还发现中等角度倾伏的拉伸线理。  相似文献   

湘赣边地区走滑断裂带致矿异常的结构样式及分形特征   总被引：4，自引：1，他引：3  

李先福  李建威  傅昭仁  王学平 《地球科学》1998,23(2):11

湘赣边地区构造岩浆带是环太平洋成矿带内最重要的高值地质矿产异常区,其中ＮＮＥ向走滑断裂明显地控制了岩浆－断陷盆地和铀及钨、锡、铅、锌、锑等的成矿作用．在区域地质环境研究的基础上,根据典型矿田（床）控矿构造分析成果,将走滑断裂带内局部性致矿地质异常归纳为：帚尾式致矿异常,棋盘格式致矿异常、辫状结环式致矿异常和拉分盆缘式致矿异常．重点讨论了各类异常的结构样式和分维特点．  相似文献   

准噶尔盆地西北缘走滑断层特征及油气地质意义   总被引：4，自引：0，他引：4  

徐怀民  徐朝晖  李震华  刘得光  陈永军  刘巍 《高校地质学报》2008,14(2)

准噶尔盆地西北缘前陆冲断带构造样式复杂多样,除规模较大的逆断层外,还发育一系列北西向的走滑断层。以高分辨率三维地震资料为基础,对断裂体系分析表明克拉玛依—百口泉地区的走滑断层可分为花状走滑断层和简单走滑断层两类,二者在成因、剖面特征等方面具有明显差别。研究结果认为走滑断层对油气的运聚成藏具有重要的双重控制作用,即能作为有效的运移通道,又能够起遮挡作用而形成圈闭。  相似文献   

青藏高原北缘阿尔金走滑边界的侧向扩展——甘肃北山晚新生代走滑构造与地壳稳定性分析     

郭召杰  ;张志诚  ;张臣  ;刘畅  ;张宇  ;王驹  ;陈伟明 《中国区域地质》2008,(10):1678-1686

对北山地区遥感影像和野外地质特征的分析表明,自阿尔金断裂带向NW方向依次出露三危山-双塔断裂、大泉断裂和红柳河断裂。这些断裂近于平行,且同为左行走滑断裂,具有相似的展布特征,空间走向均为NE40-50°,断裂系末端均发育“树枝状”分支断层．在断层夹块之间形成“多米诺”构造,构成了北山地区主要的构造样式。断层谷地沉积物分析和断层泥ESR年代学测试结果表明,三危山-双塔断裂形成于上新世（N2k）,大泉断裂形成于早更新世（1．2-1．5Ma）．而北山地区分支断层和次级断层的活动在400ka之后。对北山地区断裂构造几何学和年代学的研究表明．阿尔金断裂系晚新生代以来向NW方向的侧向扩展．是阿尔金走滑边界重要的生长方式。北山地区特殊的走滑构造组合样式．使该地区的构造变形难于在某条断层上聚集能量,而分散在若干条次级断层上的位移量又微乎其微,该地区成为“最稳定的活动区”。  相似文献   

新疆阿尔泰山南部富蕴右旋走滑断裂带晚第四纪错断水系的遥感分析研究   总被引：2，自引：2，他引：0       下载免费PDF全文

张之武  付碧宏  Yasuo Awata 《第四纪研究》2008,28(2):273-279

富蕴断裂带位于阿尔泰山南侧,横切阿尔泰山褶皱带南缘及额尔齐斯深断裂,是一条呈北北西向展布的右旋走滑断裂带。沿断裂带发育一系列错断水系、错断冲积扇、挤压脊、走滑拉分盆地等反映右旋走滑活动的典型构造地貌标志。本研究在高分辨率遥感图像和数字高程模型分析的基础上,结合野外实地构造地貌测量,对沿富蕴断裂带发育的系统错断水系特征进行了详细分析研究。研究结果表明,沿富蕴断裂带发育不同级别的错断水系,大致可划分为6级:1931年地震形成的冲沟;90m左右断距的错断水系;150m左右断距的错断水系;500m左右断距的错断水系;1500m左右断距的错断水系;2000m以上断距的错断水系。同时,结合研究区及邻区的第四纪冰川资料讨论了不同级别水系可能形成时间:恰尔沟三级支流可能形成时间为末次冰期Ⅲ阶段末期,约20ka;恰尔沟二级支流可能形成时间为末次冰期Ⅰ阶段末期,约120ka;恰尔沟一级支流可能形成于该地区冰川广泛消融的倒数第2次冰期的Ⅱ阶段末期,约为250ka;恰尔沟、水磨沟、白杨沟、乌铁布拉克河、卡布尔特河等可能形成于倒数第3次冰期Ⅱ阶段末期,约为360ka。最后,我们估算出富蕴断裂带晚第四纪以来的平均右旋走滑速率为1.46～4.99mm/a。  相似文献   

祁阳山字型构造质疑   总被引：5，自引：1，他引：4  

柏道远  李建清  周柯军  马铁球  王先辉 《大地构造与成矿学》2008,32(3)

结合区域构造演化背景及构造变形特征,对祁阳弧形构造的形成机制进行研究。分析表明,传统山字型构造机制难以解释祁阳弧形构造的诸多特征,且前人认为变形动力来源于东西向挤压应力场,也与印支期区域构造应力场实为NWW向的构造背景不符,因此祁阳弧形构造并不属典型山字型构造。基于研究区构造活动的客观实际,提出祁阳弧形构造的可能形成机制:NW向基底隐伏断裂和NNE-NE向主干断裂分别于印支期和燕山期产生强烈左旋走滑活动,从而使区域NNE向构造线在中段产生左旋偏转成为NNW向,从而形成S形的祁阳弧形构造。这一机制可较好解释祁阳弧形构造的若干特征,如关帝庙穹窿呈NWW走向、北反射弧构造形迹不显著、北弧弧顶脱位及内弧曲率大于外弧、南弧弧顶脱位、紫云-中田-高峰串珠状穹窿的形成等。上述认识对华南地区弧形构造研究具有一定启示意义:除山字型构造作用和砥柱作用外,还应注意断裂走滑等其他构造活动对弧形构造的制约,以及多次构造活动叠加对构造形迹可能造成的影响。  相似文献